![2007 honda accord 3.5 timing belt replacement schedule 2007 honda accord 3.5 timing belt replacement schedule](https://i.ytimg.com/vi/0oIXGNMzUWY/mqdefault.jpg)
A new timing belt gives you peace of mind that your engine is running optimally and is not in danger of damage. Replacing an old and worn timing belt allows you to avoid this type of problem. When a timing belt breaks while the car is running, the camshaft no longer turns. I'll button her up today test and report. I manually rotated the crank multiple times. My son held the 2x4 while I repositioned the crank and viola. I then placed a 2 x 4 across the top of the engine. It was all I could find that was the perfect size. Anyways I supported the wrench holding the rear cam into place with a book (wedged against the frame). Being a novice to mechanics this was a very good learning experience. Cool thing was I played with the crank and cam first and could actually feel when there was contact. I offset the crank and the rear cam was right on the verge of "triggering" off the tdc. I kinda figured it was going to require a bit of force but I was hesitant to do that. Let me know if this helps or if you have other questions. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure.
2007 honda accord 3.5 timing belt replacement schedule install#
Install the drive belt auto-tensioner.Ģ2. Install the upper half of the side engine mount bracket (A), then tighten the mounting bolts in the numbered sequence shown.ġ9.
![2007 honda accord 3.5 timing belt replacement schedule 2007 honda accord 3.5 timing belt replacement schedule](https://static.cargurus.com/images/site/2011/01/26/20/48/pic-1132008873297008753-1600x1200.gif)
If the camshaft pulley marks are not at TDC, remove the timing belt and repeat steps 2 through 16.ġ7. If the camshaft pulley marks are at TDC, go to step 17. NOTE: If the marks are not aligned, rotate the crankshaft 360 degrees, and recheck the camshaft pulley mark. Turn the crankshaft pulley so its white mark (A) lines up with the pointer (B). Rotate the crankshaft pulley about six turns clockwise so the timing belt positions itself on the pulleys.ġ5. Install the front upper cover (A) and the rear upper cover (B).ġ4. Install the timing belt guide plate as shown.ġ2. Install the lower half of the side engine mount bracket.ġ0. Remove the battery clamp bolt from the back cover.ĩ. Take care not to damage the timing belt during installation.Ĩ. Install the timing belt in a counterclockwise sequence starting with the drive pulley. If the auto-tensioner has extended and the timing belt cannot be installed, do the timing belt replacement procedure.Ħ. Loosely install the idler pulley with a new idler pulley bolt so the pulley can move but does not come off.ĥ. Set the camshaft pulleys to TDC by aligning the TDC marks (A) on the camshaft pulleys with the pointers (B) on the back covers.Ĥ. Set the timing belt drive pulley to top dead center (TDC) by aligning the TDC mark (A) on the tooth of the timing belt drive pulley with the pointer (B). Clean the timing belt pulleys, the timing belt guide plate, and the upper and lower covers.Ģ.
![2007 honda accord 3.5 timing belt replacement schedule 2007 honda accord 3.5 timing belt replacement schedule](https://www.cashcarsbuyer.com/wp-content/uploads/2020/12/Honda-Use-Timing-Belts-or-Chains-1200x900.jpg)
If you are installing a new belt, refer to the timing belt replacement procedure.ġ. NOTE: The following procedure is for installing a used timing belt. Vehicle Engine, Cooling and Exhaust Engine Timing Components Timing Belt Service and Repair Removal and Replacement Timing Belt Installation J35Z2 Engine The attached pictures (below) correlate with the directions and include timing mark locations. Here are the directions for replacing the belt.